Physical Address
304 North Cardinal St.
Dorchester Center, MA 02124
Physical Address
304 North Cardinal St.
Dorchester Center, MA 02124
Best Drill Bits for Drilling Hardened Steel (November 2026): 10 picks from Bosch and DEWALT, from bolt-extraction sets to a 3/4-inch bit for large holes.

A standard high-speed steel bit stops cutting the moment it meets a hardened bolt, a case-hardened plate or a seized stud. The tip overheats, the edge rounds over, and the bit rubs instead of cutting. People then push harder, which snaps small bits or work-hardens the surface and makes the next attempt worse. The Best Drill Bits for Drilling Hardened Steel depend on three things: the cobalt content of the steel, the tip geometry that keeps the bit from skating, and whether you need a full range of sizes or one specific diameter.
The short answer: the Bosch CO14B 14-Piece Cobalt Set suits most people who want an 8% cobalt M42 range up to 1/2 inch, the Bosch CO2158 31/64-Inch Cobalt Bit suits anyone who needs one larger hole in tough material, and the DEWALT DWA1240 Pilot Point Set suits people who want a familiar brand with a self-centering 135-degree tip. The rest of the list covers a 29-piece shop set, metric sets for small holes, and specialist single-size bits.
TL;DR: top picks at a glance
- Best overall: the Bosch CO14B 14-Piece Cobalt Set, 8% cobalt M42 with a 135-degree split point and sizes from 1/16 to 1/2 inch.
- Best for a single large hole: Bosch CO2158 31/64-Inch Cobalt Bit, a 0.48-inch cobalt bit rated for high-temperature work up to 1,100F.
- Best for self-centering starts: DEWALT DWA1240 Pilot Point Set, a 135-degree pilot point tip in a clear-lid case.
- Best for metric work: STROTON Metric M42 Cobalt Set, 8% cobalt in 13 sizes from 1.5 to 6.5 mm.
| # | Product | Best for | Cobalt Grade | Sizes | Tip Angle |
|---|---|---|---|---|---|
| 1 | Bosch CO14B 14-Piece Cobalt Set | All-round hardened steel | M42, 8% cobalt | 1/16 to 1/2 in | 135° |
| 2 | Bosch CO2158 31/64-Inch Cobalt Bit | One large hole | Cobalt (percentage not listed) | 31/64 in | 118° |
| 3 | DEWALT DWA1240 Pilot Point Set | Self-centering starts | Cobalt alloy steel (percentage not listed) | Not listed | 135° |
| 4 | STROTON Metric M42 Cobalt Set | Metric small holes | M42, 8% cobalt | 1.5 to 6.5 mm | 135° |
| 5 | IRWIN 3018002 29-Piece Cobalt Set | Complete shop range | 5% cobalt | 1/16 to 1/2 in | 135° |
| 6 | Axelord 13-Piece M35 Cobalt Set | Compact fractional set | M35, 5% cobalt | 1/16 to 1/4 in | 135° |
| 7 | RCINDUS 17/64-Inch Cobalt Bits | Spare bolt-out bits | M35, 5% cobalt | 17/64 in (4 bits) | 135° |
| 8 | BECOLLO 3/4-Inch Cobalt Bit | Large-diameter holes | 5% cobalt | 3/4 in (2 bits) | 135° |
| 9 | LingGan Metric M35 Cobalt Set | Light metric jobs | M35, 5% cobalt | 1.5 to 6.5 mm | Not listed |
| 10 | STROTON Fractional M35 Cobalt Set | Fractional bolt removal | M35, 5% cobalt | 1/16 to 1/4 in | 135° |

Pros:
Cons:
Best for: A home mechanic or fabricator who wants one cobalt set that covers pilot and clearance holes in hardened bolts, brackets and plate.
Check current price on Amazon →
The Bosch CO14B is the only set here that combines an 8% cobalt M42 grade with a range that reaches 1/2 inch. The STROTON Metric M42 Cobalt Set shares the same alloy, but it stops at 6.5 mm, roughly 1/4 inch. For work that spans pilot holes through to 1/2-inch clearance holes, the Bosch set covers more ground.
Buyers who use it on mild and hardened steel report fast, clean cuts, including through 10-gauge steel. The common complaint is that the smallest sizes can break if the drill wobbles, which is true of any thin bit. Use a center punch, start slowly and keep cutting fluid on the tip.
It is the wrong choice if you only need metric sizes under 6.5 mm or one specific large diameter. In the first case the STROTON Metric M42 Cobalt Set is more focused, and in the second the Bosch CO2158 31/64-Inch Cobalt Bit or the BECOLLO 3/4-Inch Cobalt Bit makes more sense.

Pros:
Cons:
Best for: A fabricator or trailer builder who needs one 31/64-inch hole through thick hardened or stainless steel.
Check current price on Amazon →
This is the specialist in the top three. Where the Bosch CO14B set tops out at 1/2 inch, the CO2158 gives you a dedicated 31/64-inch bit with a long 5-7/8-inch body. That reach helps when the hole passes through thick stock or a boxed section.
The 118-degree point has no split point listed, so a center punch and a small pilot hole are essential. One buyer drilled 1/4-inch 316 stainless with a 1/8-inch pilot, slow speed and canola oil as lubricant, and the cut was quick and clean. That workflow is the right one for any bit this size.
Skip it if you are drilling many different diameters. The Bosch CO14B 14-Piece Cobalt Set or the IRWIN 3018002 29-Piece Cobalt Set covers a spread of sizes for the same type of work.

Pros:
Cons:
Best for: A tradesperson who already uses DEWALT storage and wants a self-centering cobalt set for steel and stainless.
Check current price on Amazon →
The DEWALT DWA1240 is the organization pick. The pilot point and clear case make it quick to use on a jobsite, and the bit-bar design lets you pull out only the sizes you are using. For starting accuracy it competes with the split-point Bosch CO14B 14-Piece Cobalt Set.
The trade-off is the lack of stated cobalt grade. The Bosch set states 8% M42, and the STROTON Metric M42 Cobalt Set does the same, so if the hardest material is your priority, those are the safer bets on paper.
Choose a different set if you need metric sizes. The STROTON Metric M42 Cobalt Set covers 1.5 to 6.5 mm and keeps the sizes in the units your fasteners use.

Pros:
Cons:
Best for: A machinist or hobbyist working with metric hardware who needs small, high-grade cobalt bits.
Check current price on Amazon →
This set also comes in a grey version. Its main strength is the 8% cobalt M42 grade in the small metric range, which is where hardened-steel work often happens: pilot holes, tapping preparation and small fastener holes.
The weakness is size. Nothing exceeds 6.5 mm, so the Bosch CO14B 14-Piece Cobalt Set is the better pick if you need to step up to 1/2 inch. Compared with the LingGan Metric M35 Cobalt Set, which covers the same range in 5% cobalt, this one offers the higher grade and a stated tip angle.

Pros:
Cons:
Best for: A workshop that needs fine fractional sizing for tapping and fitting in tough steel.
Check current price on Amazon →
The IRWIN set is the completeness pick. If you routinely need 17/64 or 21/64 inch holes, a 14-piece set will leave gaps, and the 29 sizes here fill them. That is its advantage over the Bosch and DEWALT sets.
For occasional hardened-steel jobs it is more than you need. The Axelord 13-Piece M35 Cobalt Set covers 1/16 to 1/4 inch in a smaller case, and the Bosch CO14B 14-Piece Cobalt Set has the higher cobalt content.

Pros:
Cons:
Best for: A DIYer who drills small holes in stainless, cast iron and hardened brackets and wants a compact set.
Check current price on Amazon →
The Axelord covers the same 1/16 to 1/4 inch range as the STROTON Fractional M35 Cobalt Set, with a parabolic flute rather than a standard spiral. In practice the choice between them comes down to flute design and case layout.
If you need larger sizes, step up to the Bosch CO14B 14-Piece Cobalt Set or the IRWIN 3018002 29-Piece Cobalt Set, both of which reach 1/2 inch.

Pros:
Cons:
Best for: Someone with a repetitive job at 17/64 inch, such as bolting through steel frames or removing seized hardware.
Check current price on Amazon →
Where the Bosch CO2158 31/64-Inch Cobalt Bit is a single large bit, the RCINDUS pack is a multipack of a mid-size bit. That suits repetitive work: one buyer used three of four bits across a series of holes in a trailer steel frame. After drilling, treat any exposed bare edges with a rust converter so the new holes do not start corroding.
It is the wrong choice if your holes vary in size. Pick the Axelord 13-Piece M35 Cobalt Set for a range of small fractional sizes.

Pros:
Cons:
Best for: A fabricator or maintenance technician who needs 3/4-inch holes in hard steel or cast iron.
Check current price on Amazon →
Large-diameter bits demand torque. Use a drill with a low gear and a side handle. Do not use hammer mode: a hammer drill is for masonry, and the percussion action damages a cobalt cutting edge in steel.
The pair gives you a spare. If you only need holes up to 1/2 inch, the Bosch CO14B 14-Piece Cobalt Set is the more practical option, and for a 31/64-inch hole the Bosch CO2158 31/64-Inch Cobalt Bit is nearer to the size.

Pros:
Cons:
Best for: A hobbyist who wants a low-commitment metric set for thin stainless, aluminum and light metal work.
Check current price on Amazon →
This set sits below the STROTON Metric M42 Cobalt Set because it offers a lower cobalt grade and fewer stated details. Its straight flute and unlisted tip angle make it a lighter-duty choice for hardened steel.
Choose it for thin material and precision checks. If you need dependable results in genuinely hardened steel, the STROTON metric set or the Bosch CO14B 14-Piece Cobalt Set is the stronger choice.

Pros:
Cons:
Best for: A mechanic who removes broken bolts and studs and wants a hard-edged fractional set.
Check current price on Amazon →
The STROTON fractional set is nearly identical in range to the Axelord 13-Piece M35 Cobalt Set. The main differences are the 3-flat shank and the stated 68 HRC rating, versus Axelord's black oxide finish and parabolic flute.
It lands last because it offers no spec advantage over the higher-ranked sets and has little documented feedback. If you want more range, the Bosch CO14B 14-Piece Cobalt Set reaches 1/2 inch with higher cobalt content.
The core trade-off is hardness against brittleness. Cobalt bits keep their edge at high heat, but they are less forgiving of flex and side load than softer high-speed steel. Very hard tool steel can also exceed what any cobalt bit can handle, and that is a job for carbide tooling.
Before choosing, check these project details:
Cobalt content determines how well the bit holds its edge as heat builds. M42 steel with 8% cobalt, as in the Bosch CO14B 14-Piece Cobalt Set and the STROTON Metric M42 Cobalt Set, offers the highest heat resistance among the listed products. M35 steel with 5% cobalt, as in the IRWIN 3018002 29-Piece Cobalt Set and Axelord 13-Piece M35 Cobalt Set, is a step down but suits most repair work.
Higher cobalt also means a more brittle bit. Small sizes in any grade snap if you rock the drill, so use slow speed, steady pressure and cutting oil. Wear welding gloves when drilling thick steel, because chips and the bit itself get hot enough to burn.
A 135-degree split point reduces walking on smooth, hard surfaces and needs less thrust than a 118-degree tip. The DEWALT DWA1240 Pilot Point Set, Bosch CO14B 14-Piece Cobalt Set and RCINDUS 17/64-Inch Cobalt Bits all use a 135-degree tip.
The Bosch CO2158 31/64-Inch Cobalt Bit uses a 118-degree tip with no split point listed. That is workable with a center punch and pilot hole, but it is less forgiving. Always mark the spot and start with a small bit on hard surfaces.
A set suits mixed work. The IRWIN 3018002 29-Piece Cobalt Set offers the finest steps, while the Axelord 13-Piece M35 Cobalt Set and STROTON Fractional M35 Cobalt Set cover small sizes compactly.
Single bits suit specific jobs. The BECOLLO 3/4-Inch Cobalt Bit and Bosch CO2158 31/64-Inch Cobalt Bit deliver larger diameters that sets do not include, and the RCINDUS 17/64-Inch Cobalt Bits pack gives you spares of one size.
Straight shanks fit most chucks, but a 3-flat shank grips better under load. The Bosch CO14B 14-Piece Cobalt Set, STROTON Fractional M35 Cobalt Set and BECOLLO 3/4-Inch Cobalt Bit all use 3-flat shanks.
For the 3/4-inch bit, the 1/2-inch reduced shank needs a 1/2-inch chuck and a drill with enough torque. A small cordless drill will stall, so check the chuck size before ordering.
A cobalt bit with a 135-degree split point is the standard answer. The Bosch CO14B 14-Piece Cobalt Set is the top pick because it uses 8% cobalt M42 steel and covers sizes up to 1/2 inch. For one larger hole, the Bosch CO2158 31/64-Inch Cobalt Bit is a dedicated option.
Cobalt is the better choice because the cobalt is in the steel itself and holds its hardness at high temperature. Titanium is a surface coating that wears off, although the Bosch CO14B 14-Piece Cobalt Set combines a titanium finish with cobalt steel. For maximum heat resistance, look for the 8% M42 grade used in the Bosch and STROTON Metric M42 Cobalt Set.
Yes for larger bits, because the chisel edge of a big bit needs a lot of thrust. Start with a small cobalt bit from a set like the IRWIN 3018002 29-Piece Cobalt Set, then step up to the final size. This matters most with the BECOLLO 3/4-Inch Cobalt Bit and the Bosch CO2158 31/64-Inch Cobalt Bit.
Use slow speed with steady pressure and cutting oil. Fast speed builds heat and dulls even cobalt, and small bits like those in the Axelord 13-Piece M35 Cobalt Set break if you rock the drill. Large bits need the lowest speed and the most torque.
Yes, all ten products are listed for stainless steel or hard metal. Results vary by size and technique, and some users find the STROTON Metric M42 Cobalt Set less suited to stainless. The LingGan Metric M35 Cobalt Set has been used for long runs in thin stainless sheet.
Small to mid-size bits with a split point do the job, and the STROTON Fractional M35 Cobalt Set and RCINDUS 17/64-Inch Cobalt Bits are aimed at that task. The Bosch CO14B 14-Piece Cobalt Set also handles bolt removal, with a wider size range. Use a center punch and slow speed to avoid walking off the bolt.
Best Drill Bits for Drilling Hardened Steel for most buyers start with Bosch CO14B 14-Piece Cobalt Set: it uses 8% cobalt M42 steel, a 135-degree split point and a size range from 1/16 to 1/2 inch in a case. Its main weakness is that the smallest bits can snap under side load, and nothing larger than 1/2 inch is included.
For alternatives by use case, the DEWALT DWA1240 Pilot Point Set suits those who want a self-centering tip and DEWALT storage. The IRWIN 3018002 29-Piece Cobalt Set suits a workshop that needs fine 1/64-inch steps, and the STROTON Metric M42 Cobalt Set is the pick for metric hardware with the same 8% cobalt grade.
The specialist picks fill specific gaps. The Bosch CO2158 31/64-Inch Cobalt Bit and BECOLLO 3/4-Inch Cobalt Bit handle larger holes, the RCINDUS 17/64-Inch Cobalt Bits give you spares for repeated work, and the Axelord 13-Piece M35 Cobalt Set, STROTON Fractional M35 Cobalt Set and LingGan Metric M35 Cobalt Set cover small sizes with 5% cobalt. If you are still undecided, buy the Bosch CO14B set first and add a single large bit only when a job calls for it.
[…] oil. For a project that is dominated by hardened plate, compare these general-purpose sets with a drill bit for drilling hardened steel, which may suit the specialist job […]
[…] tougher stock, read our guide to the drill bit for drilling hardened steel before you commit, because hardness above this rating needs a different bit […]
[…] under sustained pressure. Use slow speed and cutting fluid. For truly hardened stock, a dedicated drill bit for drilling hardened steel is the better tool, because M42 is built for tough alloys rather than through-hardened tool […]
[…] by flute length. For deeper bores, back out often to clear chips. If your project includes metal, a drill bit for drilling hardened steel is a different tool, since Forstner bits are made for wood and […]